- Ordered and paid by 1 p.m. (German time) — shipped today
- Specialist mail order from Hannover — advice by phone and email
- PayPal, Klarna, credit card, bank transfer
In detail
All about the Mad Heaters Tempest 2 Slim Ball Vape for Torch and Induction
The Mad Heaters Tempest 2 Slim is a mechanical ball vape for dried herbs. It runs with no battery and no electronics: you heat the cap, which holds around 40 quartz balls, with a torch lighter or an induction heater, and it releases the stored heat into your herbs as you draw. The cap and heating principle come from the Mad Heaters Tempest 2, while the stem is slimmer: 316 stainless steel, 14.5 mm in diameter, 122 mm long and light at 61 g. It's available in Stainless Steel with a black heat shield and in All Black with black PVD-coated stainless steel.
The Ball Head as a Heat Reservoir
The cap holds around 40 quartz balls, each 3 mm in diameter. They absorb the heat and pass it on to the air flowing through. This means your herbs are heated mainly by convection, in other words by hot air instead of a hot wall. Our guide to convection vaporizers explains how this shows in the flavor.
The head is designed to fully vaporize a load with a single heat-up. The balls are swappable: Mad Heaters lists ruby, zirconia, silicon carbide and stainless steel as well as a two-piece heating core as alternatives. Heavier fills store the heat longer and heat up more gently, lighter ones respond faster.
Needle and Click Show the Temperature
There's no display. Instead, a needle on the cap shows how hot it is, and an audible click tells you when it's ready. The first click usually comes at the lower end of the right range. You can read more about sensible temperatures in our guide to vaporizer temperatures.
Heating with a Torch Lighter or Induction
With a torch lighter, you heat the cap from a distance of about 1 cm while slowly rotating the device. Mad Heaters recommends a double or triple flame or a medium single flame. A jet lighter like the Tobaliq X6 XL JET Flame lighter delivers the heat you need.
An induction heater gives you more even results. According to the manufacturer, the approved models are the iSpire Wand and the YLL 3.0. On the YLL 3.0 at 80 W, the stainless steel cap with quartz balls takes around 39 to 43 seconds, and a cap that's still warm takes 8 to 12 seconds less. On the iSpire Wand, the opening must be at least 14.0 mm wide. Our article on induction heaters shows how induction heaters work with mechanical vaporizers.
Over time, the cap discolors at the induction sleeve. This comes from the high heat and is normal.
Four Fill Levels
Using the included tube, you set the bowl screen to one of four levels: approx. 0.05 g, 0.1 g, 0.15 g or 0.2 g. The smallest level is new on the Slim. For half and three-quarter fills, the bowl screen tool helps you out. It's already included and is also available separately as a replacement.
Airflow, Cooling and Water Filter
You adjust the airflow in two places: at the cap via the induction sleeve and at the stem via a small ring below the heat shield. This lets you set the draw anywhere from loose to tight.
A replaceable cooling coil sits inside the stem. The medium length comes included. With the end of its stem, the Slim fits directly into a 10 mm water filter adapter. Some 14 mm adapters also fit, as long as at least 45 mm of the stem fits inside.
Tempest 2 Slim vs. Tempest 2
The cap and heating system are the same on both models, and the replacement cap and replacement chamber from Mad Heaters fit both. The Slim has a narrower stem with a heat shield made of PPS plastic and the additional 0.05 g fill level. The mouthpiece, heat shield and wood sleeve of the Tempest 2, on the other hand, don't fit the Slim. For the Slim, there's its own Dark Brown wood sleeve.
Who Is the Tempest 2 Slim For?
The Slim is made for anyone looking for a vaporizer that needs no battery at all and who wants to work with a flame or an induction heater. If you already know a pen-style vaporizer like a DynaVap, you'll find your way around quickly. There's no degree readout; you read the temperature from the needle and the click. If you expect numbers on a display, an electric device will suit you better. You'll find more devices of this type among our mechanical vaporizers.
How to Use the Tempest 2 Slim
- Clean all parts before first use. Loosen the screw on the cap once and carefully retighten it, as it can come loose during shipping.
- Unscrew the cap, fill the chamber with ground herbs, press them down only lightly and gently screw the cap back on.
- Heat the cap with the torch lighter while rotating it, or in the induction heater, and keep an eye on the needle and the click.
- Draw long and slowly while covering most of the air inlet on the stem.
- Hold the hot cap with a magnet or in the Tempest Case, twist it off and empty the chamber. The cap stays hot for several minutes.
Cleaning and Care
Before first use and about every 100 fills, Mad Heaters recommends a deep clean: soak the assembled device in 99% isopropyl alcohol for at least 30 minutes, then rinse it with warm water and let it dry completely. Remove a wood sleeve beforehand. In between, it's enough to clean the cooling coil and stem with isopropyl alcohol and cotton swabs. After each wet clean, heat the empty cap once so the remaining moisture evaporates. You'll find more tips in our guide on cleaning your vaporizer.
Technical Specifications
| Type | mechanical ball vape, no electronics |
| Heating principle | mainly convection, approx. 40 quartz balls (3 mm) |
| Heat source | torch lighter or induction heater (approved: iSpire Wand, YLL 3.0) |
| Heat-up time | approx. 39–43 s on the YLL 3.0 at 80 W |
| Temperature indicator | needle and click |
| Capacity | approx. 0.05 / 0.1 / 0.15 / 0.2 g |
| Airflow | adjustable at cap and stem |
| Material | 316 stainless steel, PPS plastic heat shield; All Black: black PVD-coated |
| Dimensions | 122 × 14.5 mm |
| Weight | 61 g |
| Water filter | fits 10 mm adapters |
What's in the Box:
- 1× Mad Heaters Tempest 2 Slim (Stainless Steel or All Black)
- approx. 40 quartz balls (3 mm) in the head plus a few spare balls
- 1× cooling coil, medium length
- 4× spare O-ring (3× 6 × 1 mm, 1× 8 × 1 mm)
- 2× bowl screen
- 2× ball retainer screen
- 1× tube for setting the bowl screen
- 1× bowl screen tool
- 1× 2 mm screwdriver bit








